Product Code: IC-NOD-005
Detachable human-machine interface for the Fieldlogger Data Logger. This little HMI fits into the front of our FieldLogger, allowing the monitoring of channels, live view of channels as a graph, alarms monitoring and some basic configuration of the FieldLogger's communication parameters (ethernet network settings, Modbus slave settings)
Product Code: IC-NOD-0101
LogBox Connect BLE Magnetic Mounting Plate allows you to easily mount the datalogger to a steel plate.
Product Code: IC-B-513
B-513 Logic Input/Output cable, 2 metres in length, bare wire end.
Product Code: IC-CB15
Provides convenient screw terminals for the 12 digital I/O lines on the DB15 connector of compatible LabJack devices. Includes a screwdriver. Not compatible with the U12.
Product Code: IC-CB25
Provides screw terminal connections for the LabJack U12's 16 extra digital I/O. A screwdriver and DB25 cable are included. For the LabJack U12 only.
Product Code: IC-CB37
Provides convenient screw terminals for the DB37 connector on the LabJack U6, UE9, and T7. Includes a screwdriver. Compatible with LJTick signal-conditioning modules.
Product Code: IC-EB37
Just like any breadboard, the EB37 is very useful for testing and validating electronic designs, but it also has a few different power supply rail voltages and breaks out LabJack I/O right next to your design.
Product Code: IC-EI1034
Easy to use and very accurate temperature probe from Electronic Innovations Corp. Features a waterproof stainless-steel probe, a high-level linear output of 10 mV per degree F, a typical accuracy of +/- 0.4 degrees F (+/- 0.22 degrees C) at room temperature, and a range of 0 to +230 degrees F (-17 to +110 degrees C, with U3/UE9).
Product Code: IC-EI1050
Uses two digital lines on any LabJack to retrieve temperature and relative humidity measurements. Featuring the Sensirion SHT11 sensor, it provides 14-bit temperature readings and 12-bit humidity readings. An enable line is provided to allow multiple EI-1050 probes to be connected to a single LabJack.
Product Code: IC-B-569
Graphtec Lithium-ion Battery.
Product Code: IC-GL-820-CASE
Graphtec GL820 Carry Case, plastic with foam insert.
Product Code: IC-DB15
LabJack DB15 Cable (6 ft)
Product Code: IC-DB25
LabJack DB25 Cable (3ft)
Product Code: IC-DB37
A three foot DB37 cable, useful for connections between the Mux80 and CB37 Terminal Board(s). Also can be used to connect a U6, UE9, or T7 to a CB37 or Mux80.
Product Code: IC-LabJackEthernetCable
LabJack LabJack Ethernet Cable
Product Code: IC-T7 Power
LabJack T7 Power Supply
Product Code: IC-TKADDIN
LabJack TKAD DIN Clip
Product Code: IC-UE9Power
LabJack UE9 Power Supply
Product Code: IC-LabJackUSBCable
LabJack USB Cable
Product Code: IC-LJTick-CurrentShunt
The LJTick-CurrentShunt (LJTCS) is a signal-conditioning module designed to convert a 4-20 mA current loop input signal into a 0.47-2.36 volt signal compatible with the LabJack U3, U6, UE9, T7, or T4. The 4-pin design plugs into the standard AIN/AIN/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, T7, and T4.
Product Code: IC-LJTick-DAC
Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. Plugs into any digital I/O block (e.g. FIO4/FIO5), and thus up to 10 of these can be used per LabJack to add 20 analog outputs. Works with T-Series devices (T7, T4) and any UD family device (U3/U6/UE9).
Product Code: IC-LJTick-DigitalOut5V
Converts 3.3V digital outputs to 5V digital outputs. Easily control 5V relays, or interface with a 5V logic device.
Product Code: IC-LJTick-Divider
The LJTick-Divider (LJTD) is a signal conditioning module designed to take two single-ended higher voltage analog signals, and divide them by a specified value.
Product Code: IC-LJTick-InAmp
Signal-conditioning module provides two instrumentation amplifiers ideal for low-level signals such as bridge circuits (e.g. strain gauges) and thermocouples. Each amplifier converts a differential input to single-ended.
Product Code: IC-LJTick-InBuff
Very low bias current (1pA) input buffer which can directly measure pH sensors (electrode type sensors) and other weakly driven or high source impedance signals. The analog inputs on our compatible DAQ products (U3, U6, UE9, T7, T4) have typical bias currents on the order of 20 nA, which is quite low, but the LJTick-InBuff reduces that dramatically.
Product Code: IC-LJTick-LVDigitalIO
A bidirectional logic shifting board for converting 3.3V logic down to 2.5V or 1.8V. There is also a VOUT terminal which can source power at the selected voltage. Useful for users who have external boards that run on lower logic thresholds, or simply want a 3.3V, 2.5V, or 1.8V supply.
Product Code: IC-LJTick-OutBuff
Increases the output current of the DAC outputs on LabJack devices. Can also be used for switched 3.3V when attached to a 3.3V digital I/O line. LabJack devices cannot output more than about 15mA on their DAC0 and DAC1 analog outputs, so this accessory is very helpful for users who want to increase that capability. One common application is to control the speed of a low voltage DC motor.
Product Code: IC-LJTick-Proto
The LJTick-Proto (LJTP) consists of an 8x8 grid of holes for prototyping custom signal-conditioning ticks. The 4-pin design plugs into the standard AIN/AIN/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, T7, and T4. Includes 3 loose pieces: the PCB, a 4-position screw terminal, and a right-angle pin header.
Product Code: IC-LJTick-RelayDriver
Allows 2 digital I/O lines to each control a relay or other moderate load. The 4-pin design plugs into the standard DIO/DIO/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, T7, and T4. Each DIO controls a switch to ground (i.e. open-collector) that can hold off up to 50 volts and can sink up to 200 mA.
Product Code: IC-LJTick-Resistance
The LJTick-Resistance (LJTRx) makes it easy for LabJack devices to measure resistive sensors. This tick gives users a regulated 2.5V signal that can be used as a excitation voltage and a known resistance value in series with a sensor input line. This gives users the ability to calculate the resistance of their connected sensor.
Product Code: IC-LJTick-VRef
The LJTick-VRef is a Voltage reference accessory that outputs a stable 2.5V or 4.096V signal. These ticks are commonly used as an excitation voltage for various circuits. The IOA and IOB lines are pass-through terminals, and do not interact with the accessory in any way. Available in two models.
Product Code: IC-LM34CAZ
The LM34CAZ is ideal for cold-junction compensation(CJC) temperature measurements. Customers who are using thermocouples on an external CB37 terminal board can wire this sensor to a nearby analog input, and correlate the CJC offset within software.
Product Code: IC-Mux80
Analog input expansion board that adds 80 analog input channels. It can be connected to a U6, UE9, or T7 directly through the DB37 connector.
Product Code: IC-PS12DC
Controlled through 12 digital outputs, the PS12DC can switch power sources ranging from 5 to 28V DC. Attach the PS12DC to the DB15 connector presented on all compatible devices, and toggle the states of the EIO and CIO digital output lines to turn the switches on/off.
Product Code: IC-RB12
Provides 12 industry standard relay module sockets to a U3, U6, UE9, T4, or T7. Commonly used to interface a LabJack with high voltages/currents. The RB12 relay board connects to the DB15 connector on the LabJack, using the 12 EIO/CIO lines to control up to 12 I/O modules.